Datalogic Scanning DS6400 Manual do Utilizador Página 14
- Página / 122
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
MASTER/SLAVE LONWORKS INSTALLATION
The following can be used as a checklist to verify all the steps necessary to complete
installation of the DS6400 scanner in a Master/Slave Lonworks network.
1) Read all information in the section “Safety Precautions” at the beginning of this manual.
2) Correctly mount the scanner using the bracket provided according to the information in
par. 2.2.2 and position it at the correct reading distance according to your model as
shown in par. 4.4.
3) Make electrical connections to your DS6400 scanner by:
a) Connecting the DS6400
Master scanner to the C-BOX 100 by means of one of the
cables provided as accessory (see par. 1.5).
b) Correctly inserting the BTK-6000 terminator in the DS6400 Master reader according
to the information given under “Local Lonworks Network” in par. 2.3.2 and par. 2.7.5.
c) Completing the system wiring adding as much slave scanners as required by your
system layout (refer to par. 2.7).
d) Correctly inserting the BTK-6000 terminator in the last DS6400 Slave reader of the
network according to the information given under “Local Lonworks Network” in par.
2.3.2 and par. 2.7.5.
4) Install and run the Genius™ configuration program from the CD-ROM provided.
Configure the Local Lonworks Network using one of the procedures given below:
a) Configure the entire network through the Master as described in par.
b) Configure the Master as described in par. 3.2.2 and locally define each slave scanner
address as described in par. 3.2.3.
c) Define each scanner, master and slaves (with their addresses), by using the scanner
keypad according to the information given in par. 2.9.1.
5) Configure the Master scanner through the Genius™ program. The main steps are:
• Select the codes to be read
• Set-up the communication parameters
• When PackTrack™ is required, perform PackTrack™ calibration, see par. 4.2.1
• Define data formatting parameters
6) Configure each Slave scanner through the Master scanner using Genius™. The main
steps are:
• Select the codes to be read
• When PackTrack™ is required, perform PackTrack™ calibration, see par. 4.2.1
NOTE
Fine tuning of the scanner position for barcode reading can be
accomplished by performing a test through the SPY configuration tool
in Genius™.
7) Send the configuration to the Master.
xiv
- Reference Manual 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- POWER SUPPLY 8
- CE COMPLIANCE 8
- WEEE COMPLIANCE 8
- GENERAL VIEW 10
- Laser Safety Label 11
- Laser Beam Output Window 11
- GUIDE TO INSTALLATION 13
- 1 INTRODUCTION 17
- DS6400 - 10X - 0YY 18
- INTRODUCTION 19
- 1.4 INDICATORS 21
- 1.5 ACCESSORIES 22
- 2 INSTALLATION 23
- 2.2 MECHANICAL MOUNTING 24
- 2.2.1 Mounting the Scanner 24
- INSTALLATION 27
- 2.3 ELECTRICAL CONNECTIONS 29
- (with INT-30 only) 30
- Main Interface 32
- RS232 Interface 32
- RS485 Full-Duplex Interface 33
- RS485 Half-Duplex Interface 34
- Auxiliary Interface 35
- EXTERNAL TRIGGER/ENCODER 36
- Outputs 38
- 2.3.2 Lonworks Connectors 40
- Network Termination 41
- Lonworks Interface 42
- 2.3.3 Ethernet Connector 44
- Figure 41 – Inverted Cable 45
- 25-pin male connector 48
- 2.6 TYPICAL INSTALLATIONS 51
- 2.6.1 Standard Installation 51
- ATTENTION 52
- 2.7 TYPICAL LAYOUTS 52
- 2.7.1 Point-to-Point 52
- Main Serial Interface 54
- Fieldbus 56
- 2.7.5 Local Lonworks Network 58
- Small Synchronized Network 59
- Large Synchronized Network 61
- 2.7.6 Fieldbus Network 63
- Network 63
- 2.8 FLASH™ DYNAMIC FOCUS 64
- 2.8.1 Fixed Mode 64
- 2.8.2 Continuous Mode 64
- 2.8.3 Triggered Mode 65
- 2.8.4 D-FLASH™ Mode 65
- 2.9 KEYPAD AND DISPLAY 66
- 2.9.1 Internal Net 66
- 2.9.2 Test Mode 67
- 3 SOFTWARE CONFIGURATION 68
- SOFTWARE CONFIGURATION 69
- On Line Operating Mode 70
- Automatic Operating Mode 70
- Net-Autoset 73
- Express Network Setup 73
- Network Wizard 74
- 3.4 PARAMETER DEFAULT VALUES 77
- 4 READING FEATURES 81
- Conveyor 82
- Laser Beam 82
- SPY ICON 84
- Position 1 85
- Position 2 85
- Position 3 85
- 4.3 PERFORMANCE 86
- 4.3.1 Reading Conditions 86
- 4.4 READING DIAGRAMS 88
- 4.4.1 DS6400 Standard Model 89
- Position = 90 cm 91
- Position = 60 cm 99
- Min. Reading 100
- Distance 100
- Max. Reading 100
- Global Reading 101
- Position = 95 cm 101
- READING FEATURES 105
- MAINTENANCE 109
- TROUBLESHOOTING 111
- 7 TECHNICAL FEATURES 114
- TECHNICAL FEATURES 115
- GLOSSARY 116
- Parameter Groups 120
- Default Values; 61 120
- DECLARATION OF CONFORMITY 121
Samsung TH026EAV1 manuels
Manuels d'utilisation et guides de l'utilisateur pour Lecteurs de CD Samsung TH026EAV1.
Nous fournissons des manuels en pdf Samsung TH026EAV1 à télécharger gratuitement par type de document :
Comentários a estes Manuais